Broan AWEPD48SS Guía de instalación

Busca en linea o descarga Guía de instalación para No Broan AWEPD48SS. Broan AWEPD48SS Installation Guide Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 4
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
FOLLOW HOOD INSTALLATION GUIDE STEPS 1 TO 3
PRIOR TO WALL EXTENSION INSTALLATION.
Measure and mark a
level line on wall above
cooktop location for the
wood mounting strip.
Remove wood
mounting strip from
back of hood.
Center wood mounting
strip over location.
Use no. 10 x 2’ flat
head screws to secure
the mounting strip to
the wall.
Make sure to hit the
wall studs.
Insert house wiring through top, right hole.
Rest the back cavity of the wall extension on wood mounting
strip (provided with the hood). Secure upper portion of the wall
extension to wood mounting strip with (up to) 6 no. 8 x 5/8”
screws (included).
Drill two 3/16” diameter holes into the wall for wall anchors
through two of the existing lower holes of the wall extension.
Then, install both wall anchors, both washers and 2 no. 8 x 5/8”
screws (included).
WALL EXTENSION AWEPD SERIES
INSTALLATION INSTRUCTIONS
THIS KIT CONTAINS:
1 W
ALL EXTENSION
1 PARTS BAG (SERVICE PART NO. S97018867) INCLUDING: 1 WIRE
CLAMP, 8 NO. 8 X 5/8" SCREWS, 2 WALL ANCHORS, 2 WASHERS AND
8 NO. 10-32 X 3/8" SCREWS
Due to the weight of this hood, ensure that the wood strip is
attached to all of the available studs (2 studs minimum for
36" width hood and 3 studs minimum for 48" width hood);
not into the wall alone.
CAUTION
HD0478A
1. Wall
2. Wood mounting
strip
3. Flat head screw
4. Wall anchor location
5. Back of wall
extension outline
6. Wall studs
HD0475
4 TO 6 SCREWS
2 WALL ANCHORS/WASHERS/SCREWS
Using pliers, unfold to 90° both wall extension metal tabs to
align hood during installation.
FOLLOW HOOD INSTALLATION GUIDE STEPS 4 TO 6
BEFORE INSTALLING HOOD.
HR0071
90°
Remove the hood
electrical compartment
and insert house wiring
through hood wire
clamp.
Rest the back cavity of
the hood on wall
extension metal tabs.
Secure hood to wall
extension using 8
provided no. 10-32 x
1/2” quadrex screws (4
on both sides). See
illustration at right.
Tighten wire clamp.
SCREW
LOCATIONS
TAB
FOLLOW HOOD INSTALLATION GUIDE STEPS 9 TO 11 TO
FINALIZE HOOD INSTALLATION
.
Vista de pagina 0
1 2 3 4

Indice de contenidos

Pagina 1 - INSTALLATION INSTRUCTIONS

FOLLOW HOOD INSTALLATION GUIDE STEPS 1 TO 3PRIOR TO WALL EXTENSION INSTALLATION.Measure and mark alevel line on wall abovecooktop location for thewoo

Pagina 2 - DIRECTIVES D’INSTALLATION

DIRECTIVES D’INSTALLATIONDE LA RALLONGE DE HOTTEDE LA SÉRIEAWEPDCET ENSEMBLE CONTIENT :• 1 RALLONGE DE HOTTE• 1 SAC DE PIÈCES (PIÈCE DE SERVICE N° S97

Pagina 3 - DE SERIE

SIGA LOS PASOS 1 A 3 DE LA GUÍA DE INSTALACIÓN DE LACAMPANA ANTES DE INSTALAR LA EXTENSIÓN DE PARED. Mida y marque sobre lapared una línea a nivelpor

Pagina 4 - 99044961C

BROAN-NUTONE ONE YEAR LIMITED WARRANTYBroan-NuTone warrants to the original consumer purchaser of its products that such products will be free from de

Comentarios a estos manuales

Sin comentarios